DataCard LM200 Uživatelská příručka Strana 59
- Strana / 109
- Tabulka s obsahem
- KNIHY
Hodnocené. / 5. Na základě hodnocení zákazníků
SR200 & SR300 Printer and LM200 & LM300 Laminator User Guide 53
Standby
Front Wait
Back Wait
Displays the value set using the Status Monitor.
Backside Cool
On
Off
Displays the value set using the Status Monitor.
Bend Remedy Temp Level Displays the value set using the Status Monitor.
See
“Bend Remedy tab” on page 36 for more information.
Speed If installed, displays the value set using the Status Monitor.
See “Bend Remedy tab” on page 36 for more information.
Heat Roller HR Control
Enable
Disable
Displays the value set using the Status Monitor.
Power Saving
OFF or up to 60
minutes
Displays the value set using the Status Monitor.
Setting
Display Counter
• Total Cnt
• Head Cnt
• Free Cnt
• Cleaning Cnt
• Error Cnt
Use the up and down arrow keys to select the card counter type:
• Total is the default setting, and displays the number of
cards printed. The Total counter cannot be reset.
• Head displays the number of complete dye panels. The
Head counter cannot be reset, however, it automatically
resets itself when the print head is replaced.
•The Free counter displays the number of cards that have
printed. The Free counter can be reset by the user.
Mode
Counter
Laminator Stat
Choose the information to display on the panel.
Contrast
0
Displays the LCD panel contrast using 7 gradations from
-3 (low contrast) to +3 (high contrast). The default setting is 0.
Buzzer ON or OFF Displays whether the electronic beep sound is ON or OFF.
The sound can indicate an error, when fewer than 20 cards
remain in the card hopper, or to confirm a menu selection.
Unit No Choose from 1 to 10 Assign the unit number when more than one printer is
connected to a PC. Each unit attached to a PC must have a
unique number. After choosing the unit number, press the
Enter key and then the Exit key. “Please, power off” is
displayed on the LCD panel. Power the printer off and then
back on.
Menu Display Settings Function
- User Guide 1
- Trademark acknowledgments 2
- Proprietary Notice 2
- Contents 3
- 5 Messages 5
- Liability statement 6
- Introduction 7
- About the printer 8
- The inside of the printer 9
- The back of the printer 10
- About the laminator 11
- Using the printer 13
- Load Supplies 14
- Remove Hopper and Cards 15
- Replace the Hopper 15
- Adjust Card Thickness 15
- Load ink ribbon 16
- Load retransfer film 17
- Load top side laminate film 18
- Take-up Spool 19
- Supply Roll 19
- Guide Shaft 19
- Metal Guides 19
- Power on 20
- Optional laminator connection 21
- Power on the laminator 21
- Power on the printer 22
- Prepare to print cards 23
- Printing cards 23
- Print cards using ID software 24
- Print from a PC application 24
- Tips for Success 25
- Viewing and changing 27
- Printing Preferences 28
- Print tab 29
- Priority of Data 31
- 1 Panel Auto 2 Panels 31
- Page Split 32
- Security Erase 33
- Printing Area Settings 34
- Printer Settings 34
- Encode tab 35
- Laminate tab 35
- Configuration tab 35
- Printing Properties 36
- Status Monitor 37
- Close the Status Monitor 38
- Printer Status tab 39
- Printer Setting tab 40
- Retransfer tab 41
- Bend Remedy tab 42
- Media Setting tab 42
- Property tab 43
- Laminator tab 44
- Printer Select tab 45
- Others tab 46
- Security Lock tab 46
- Status monitor messages 47
- “Mending 49
- Using the LCD Menus 55
- Using the Printer LCD Panel 57
- Printer Security Number 63
- Red Status Light 64
- Blue Status Light 64
- Operator Button 64
- “Laminator 65
- LCD messages” on page 84 65
- Laminator Settings 66
- Taking care of your printer 67
- Cleaning the printer 68
- Tips – Cleaning card feed 69
- Cleaning the magnetic head 70
- Cleaning the thermal head 71
- Cleaning printer fan filters 71
- Cleaning the laminator 73
- Laminator fan filter 75
- Messages 77
- Printer error recovery 78
- Transfer jam 79
- Turnover jam 80
- Retransfer section jam 81
- Printer LCD messages 83
- “Operating environment” on 85
- “Load cards” on 85
- Take -up side 86
- Laminate pressure motor 86
- Supply side 86
- Supp ly Roll 87
- Patch Position 88
- Card warping 89
- Laminator LCD messages 90
- Supplies 93
- Ink ribbon 94
- Retransfer film 94
- Laminator material 95
- Cleaning supplies 96
- Site requirements 97
- Site guidelines 98
- Ventilation clearance 99
- Printer specifications 100
- Laminator specifications 101
- Magnetic Stripe Encoding 103
- Inline Encoding 104
- Character Code Table 105
- Compliance (FCC) 107
- Regulatory compliance 108
- 11111 Bren Road West 109
- Minnetonka, MN 55343-9015 109
- 952.933.1223 109
- 952.933.7971 FAX 109
© 2020, manymanuals.cz. Všechna práva vyhrazena. | 0.050 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentáře k této Příručce